e-Elit - leading
electronic and automation component
online distributor

	Items:	Total:
	0	€0.00

Show all products categ.

Need assistance?

LED Power Supply 35W 3A 12V IP67

Features
Constant voltage design
Universal AC input / Full range
Withstand 300 VAC surge input for 5 seconds
Protections: Short circuit / Overload / Over voltage
Cooling by free air convection
Fully encapsulated with IP67 level
Fully isolated plastic case
Class II power unit, no FG
Class 2 power unit
Pass LPS
Suitable for LED lightning and moving sign applications
100% full load burn-in test
Low cost, high reliability
2 years warranty

LED strip

OUTPUT DC Voltage	12V
Rated current	3A
Current range	0 ~3A
Rated power	36W
Ripple & Noise (max.) Note.2	120mVp-p
Voltage tolerance Note.3	±5.0%
Line regulation	±1.0%
Load regulation	±2.0%
Setup, rise time Note.6	500ms, 20ms/ 230VAC 500ms, 20ms / 115 VAC at full load
Hold up time (typ.)	50ms/230VAC 16ms/115VAC at full load

INPUT Voltage range	90 ~ 264VAC 127~370VDC
Frequency range	47 ~ 63 Hz
Effiency (typ.)	84%
AC current	1.1A/115VAC 0.7/230VAC
Inrush current (max.)	Cold start 55A (width=510µs measured at 50% lpeak) at 230VAC
Leakage current	0.25mA/240VAC

PROTECTION OVERLOAD	110 ~ 150 %#37; rated output power Protection type: Hiccup mode, recovers automatically after fault conditions is removed
Over voltage	13.8 ~ 16.2V Protection type: Shut off o/p voltage, re-power on to recover

ENVIRONMENT Working temperature	-30° ~ +65°C (Refer to "Derating Curve")
Working humidity	20 ~ 90% RH non-condensing
Storage temp., humidity	-40 ~ +80°C, 10 ~ 95% RH
Temp. coefficient	±0.03%/°C (0 ~ 50°C)
Vibration	10 ~ 500Hz, 2G 10 min./1 cycle, period for 60min. each along X, Y, Z axes
SAFETY & EMC Safety standards	UL879, UL1310, CSA C22.2 No. 207-M89, CAN/CSA C22.2 No.223-M91, IP67 approved, design refer to TUV EN60950-1
Withstand voltage	I/P-O/P: 3KVAC
Isolation resistance	I/P-O/P: &100M Ohms / 500VDC / 25°C / 70% RH
EMC emission	Compliance to EN55022 (CISPR22) Class B, EN61000-3-2 Class A, EN61000-3-3
EMC immunity	Compliance to EN61000-4-2, 3, 4, 5, 6, 8, 11; EN55024, light industry level, criteria A
OTHERS MTBF	743.5K hrs min. MIL-HDBK-217F (25°C)
Dimension	148 x 40 x 30 (L x W x H)
Packing	0.34kg; 40pcs / 14.6kg / 0.63CUFT
NOTE	All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25°C of ambient temperature. Ripple & noise are measured at 20MHz of bandwidth by using a 12“ twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. Tolerance: includes set up tolerance, line regulation and load regulation. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the complete installation, the final equipment manufacturers must re-quality EMC Directive on the complete installation again. Length of the set up time is measured at first cold start. Turning ON/OFF the power supply may lead to increase of the set up time. The unit might not be suitable for lighting applications in EU countries. please check with your local authorities for the possible use of the unit.